Jump to content

Mazda RX-7

From Wikipedia, the free encyclopedia
(Redirected from RX-7)
Mazda RX-7
1994 Mazda RX-7 R2 (FD3S)
Overview
ManufacturerMazda
Also calledMazda Savanna RX-7 (Japan, 1978–1991)
Mazda ɛ̃fini RX-7 (Japan, 1991–1997)
Production1978–2002
811,634 produced[1]
AssemblyJapan: Hiroshima (Hiroshima Assembly)
Body and chassis
ClassSports car (S)
LayoutFront engine, rear-wheel-drive
PlatformMazda F
Chronology
PredecessorMazda RX-3
SuccessorMazda RX-8

The Mazda RX-7 is a front-engine, rear-wheel-drive, rotary engine-powered sports car that was manufactured and marketed by Mazda from 1978 until 2002 across three generations, all of which made use of a compact, lightweight Wankel rotary engine.

The first-generation RX-7, sometimes referred to as the SA (early) and FB (late), is a two-seater two-door hatchback coupé. It featured a 12A carbureted rotary engine as well as the option for a 13B rotary engine with electronic fuel injection in later years.

The second-generation RX-7, sometimes referred to as the FC, was offered as a two-seater coupé with a 2+2 option available in some markets, as well as in a convertible body style. This was powered by the 13B rotary engine, offered in naturally aspirated or turbocharged forms.

The third-generation RX-7, sometimes referred to as the FD, was offered a 2+2-seater coupé with a limited run of a two-seater option. Some markets were only available as a two-seater. It featured a sequentially turbocharged 13B REW engine.

More than 800,000 RX-7s were manufactured over its lifetime.[1]

First generation (SA, FB)

[edit]
First generation (SA/FB)
1980 Mazda RX-7
Overview
Model codeSA22 / FB
Also calledMazda Savanna RX-7
Production1978–1985
471,018 produced[1]
DesignerMatasaburo Maeda (1976)
Body and chassis
Body style2-door coupé
Powertrain
Engine
Transmission
Dimensions
Wheelbase2,420 mm (95.3 in)
Length4,285 mm (168.7 in)
Width1,675 mm (65.9 in)
Height1,260 mm (49.6 in)
Curb weight1,043–1,134 kg (2,300–2,500 lb)

Series 1 (1978–1980)

[edit]

Series 1 (produced from 1978 until 1980) is commonly referred to as the "SA22C" from the first alphanumeric of the vehicle identification number. Mazda's internal project number for what was to become the RX-7 was X605. In Japan, it was introduced in March 1978, replacing the Savanna RX-3, and joined Mazda's only other remaining rotary engine-powered products, called the Cosmo which was a two-door luxury coupé, and the Luce luxury sedan.

The lead designer at Mazda was Matasaburo Maeda (前田 又三郎, Maeda Matasaburō), whose son, Ikuo [ja], would go on to design the Mazda2 and the RX-7's successor, the RX-8.[2] The transition of the Savanna to a sports car appearance reflected products from other Japanese manufacturers. The advantage the RX-7 had was its minimal size and weight, and the compact rotary engine installed behind the front axle helped balance the front and rear weight distribution, which provided a low center of gravity.

In May 1980, Mazda introduced a limited production run of special North American models known as the Leathersport Models. This package was essentially an uprated GS model with added LS badges on each B-pillar, special stripes on the exterior, and LS-only gold anodized wheels (with polished outer face and wheel rim). All LS editions came equipped with special LS-only full brown leather upholstery, leather-wrapped steering wheel, leather-wrapped shift knob, removable sunroof, LS-specific four-speaker AM/FM stereo radio with power antenna (though listed as a six-speaker stereo, as the two rear dual voice coil speakers were counted as four speakers in total), remote power door side mirrors, and other standard GS equipment. Two primary options were also available; a three-speed JATCO 3N71B automatic transmission and air conditioning. The dealer could add other GS options such as a cassette tape deck, splash guards, padded center console arm rest, and others. The LS model was only ever available in three different exterior colors: Aurora White, Brilliant Black, and Solar Gold. No official production records are known to exist or to have been released. This series of RX-7 had exposed steel bumpers and a high-mounted indentation-located rear license plate, called by Werner Buhler of Road & Track magazine a "Baroque depression."

Series 2 (1981–1983)

[edit]
Mazda RX-7 Series 2 GSL (US; 1983)

The Series 2, referred to as the FB (produced from 1981 to 1983), had integrated plastic-covered bumpers, wide black rubber body side moldings, wraparound taillights and updated engine control components. While marginally longer overall, the new model was 135 lb (61 kg) lighter in federalized trim.[3] The four-speed manual option was dropped for 1981 as well, while the gas tank grew larger and the dashboard was redesigned, including a shorter gear stick mounted closer to the driver.[3] In 1983, the 130 mph (209 km/h) speedometer returned for the RX-7. The GSL package provided optional four-wheel disc brakes, front ventilated (Australian model) and clutch-type rear limited-slip differential (LSD). This revision of the SA22 was known in North America as the "FB" after the US Department of Transportation mandated 17 digit Vehicle Identification Number changeover. For various other markets worldwide, the 1981–1985 RX-7 retained the 'SA22C' VIN prefix. In the UK, the 1978–1980 series 1 cars carried the SA code on the VIN but all later cars (1981–1983 series 2 and 1984–1985 series 3) carried the FB code and these first-generation RX-7s are known as the "FB" only in Northern America.

In Japan, a very well appointed version similar to the export market GSL arrived late in 1982, called the SE-Limited. This model received two-tone paint, alloy wheels shaped like the Wankel rotor, all-wheel disc brakes, limited-slip differential, and a full leather interior. It also had the latest iteration of the 12A rotary engine, the RE-6PI with variable induction port system and 140 PS (103 kW; 138 hp).[4]

In Europe, the FB was mainly noticed for having received a power increase from the 105 PS (77 kW) of the SA22; the 1981 RX-7 now had 115 PS (85 kW) on tap. European market cars also received four-wheel disc brakes as standard.[5]

In 1984 Mazda Australia decided to produce a convertible by joining a RX7 front body with a 626 coupee rear end. To ensure rigidity, steel channel beams were welded to the floor pan. Due to the added weight, the engine used was the Japanese model 12AT introduced in 1983.rated at 121kw@ 6500rpm. It was planned and budgeted to build eighty cars a year. However after the first production run of six, Mazda Japan became aware of the project and ended it. intending in 1985 to introduce the Second Generation increased size RX7 with the larger, more powerful 13B engine. This would include a convertible model for worldwide sales. Thus, the Series 2 convertible is the rarest Mazda car built.

Series 3 (1984–1985)

[edit]
1984–1985 Mazda RX-7 (Series 3)
Series 3 Interior (US)

The Series 3 (produced 1984–1985) featured an updated lower front fascia. North American models received a different instrument cluster. GSL package was continued into this series, but Mazda introduced the GSL-SE sub-model. The GSL-SE had a fuel injected 1,308 cc (1.3 L) 13B RE-EGI engine rated at 135 hp (101 kW; 137 PS) and 133 lb⋅ft (180 N⋅m). GSL-SE models had much the same options as the GSL (clutch-type rear LSD and rear disc brakes), but the brake rotors were larger, allowing Mazda to use the more common lug nuts (versus bolts), and a new bolt pattern of 4x114.3mm (4x4.5"). Also, they had upgraded suspension with stiffer springs and shocks. The external oil cooler was reintroduced, after being dropped in the 1983 model-year for the controversial "beehive" water-oil heat exchanger.

The 1984 RX-7 GSL has an estimated 29 MPG (8.11 litres/100 km) highway/19 MPG (12.37 L/100 km) city. According to Mazda, its rotary engine, licensed by NSU-Wankel allowed the RX-7 GSL to accelerate from 0 to 80  km/h (50  mph) in 6.3 seconds.

In 1985, Mazda introduced the RX-7 Finale in Australia. This was the last of the series and brought out in limited numbers. The Finale featured power options and a brass plaque mentioning the number the car was as well as "Last of a legend" on the plaque. The finale had special stickers and a blacked out section between the window & rear hatch.

The handling and acceleration of the car were noted to be of a high caliber for its day.[citation needed] The RX-7 had "live axle" 4-link rear suspension with Watt's linkage, a 50:50 front and rear weight distribution, and weighed under 1,100 kg (2,425 lb). It was the lightest generation of the RX-7 ever produced. 12A-powered models accelerated from 0–97 km/h (60 mph) in 9.2 seconds, and turned 0.779 g (7.64 m/s²) laterally on a skid pad. The 1,146 cc (1.1 L) 12A engine was rated at 100 hp (75 kW; 101 PS) at 6,000 rpm in North American models, allowing the car to reach speeds of over 190 km/h (120 mph). Because of the smoothness inherent in the Wankel rotary engine, little vibration or harshness was experienced at high engine speeds, so a buzzer was fitted to the tachometer to warn the driver when the 7,000 rpm redline was approaching.

The 12A engine has a long thin shaped combustion chamber, having a large surface area in relation to its volume. Therefore, combustion is cool, giving few oxides of nitrogen. However, the combustion is also incomplete, so there are large amounts of partly burned hydrocarbons and carbon monoxide. The exhaust is hot enough for combustion of these to continue into the exhaust. An engine-driven pump supplies air into the exhaust to complete the burn of these chemicals. This is done in the "thermal reactor" chamber where the exhaust manifold would normally be on a conventional engine. Under certain conditions, the pump injects air into the thermal reactor and at other times air is pumped through injectors into the exhaust ports. This fresh air is needed for more efficient and cleaner-burning of the air/fuel mixture.[6]

Options and models varied from country to country. The gauge layout and interior styling in the Series 3 was only changed for the North American models. Additionally, North America was the only market to have offered the first generation of the RX-7 with the fuel-injected 13B, model GSL-SE. Sales of the first-generation RX-7 were strong, with a total of 474,565 cars produced; 377,878 (nearly eighty percent) were sold in the United States alone.

RX-7 Turbo

[edit]
Mazda Savanna RX-7 Turbo

Following the introduction of the first turbocharged rotary engine in the Luce/Cosmo, a similar, also fuel injected and non-intercooled 12A turbocharged engine was made available for the top-end model of the Series 3 RX-7 in Japan. It was introduced in September 1983.[7] The engine was rated at 165 PS (121 kW) (JIS) at 6,500 rpm. While the peak power figures were only slightly higher than those of the engine used in the Luce/Cosmo, the new "Impact Turbo" was developed specifically to deal with the different exhaust gas characteristics of a rotary engine. Both rotor vanes of the turbine were remodeled and made smaller, and the turbine had a twenty percent higher speed than a turbo intended for a conventional engine.[8] The Savanna Turbo was short-lived, as the next generation of the RX-7 was about to be introduced.

Second generation (FC)

[edit]
Second generation (FC)
Overview
Model codeFC
Also calledMazda Savanna RX-7
Production
  • 1985–1992
  • 272,027 produced[1]
DesignerAkio Uchiyama (lead designer)
Body and chassis
Body style
Powertrain
Engine
Transmission
Dimensions
Wheelbase2,431 mm (95.7 in)
Length
  • 1986-88: 4,290 mm (168.9 in)
  • 1989–92: 4,315 mm (169.9 in)
Width1,689 mm (66.5 in)
Height1,265 mm (49.8 in)
Curb weight1,223–1,293 kg (2,696–2,851 lb)
Mazda RX-7 Turbo (JDM), note the intercooler scoop on the bonnet distinguishing it from the naturally aspirated models

The second-generation RX-7 (sometimes referred to as "FC", VIN begins JM1FC3 or JMZFC1), still known as the Mazda Savanna RX-7 in Japan, featured a complete restyling much like similar sports cars of the era such as the Nissan 300ZX. Mazda's development team, led by Chief Project Engineer Akio Uchiyama (内山 昭朗), chose to focus on the American market when designing the FC, where the majority of first-generation of the RX-7 models had been sold. The team drew inspiration from successful sports cars that were popular at the time, such as studying the suspension design of the Porsche 928.[9]

While the first-generation RX-7 was a purer sports car, the second-generation RX-7 tended toward the softer sport-tourer trends of its day, sharing some similarities with the HB series Cosmo. Handling was much improved, with less of the oversteer tendencies of the previous version. The rear end design was vastly improved from the SA22's live rear axle to a more modern, Independent Rear Suspension (rear axle). Steering was more precise, with rack and pinion steering replacing the old recirculating-ball steering of the SA22. Disc brakes also became standard, with some models (S4: Sport, GXL, GTU, Turbo II, Convertible; S5: GXL, GTUˢ, Turbo, Convertible) offering four-piston front brakes. The rear seats were optional in some models of the FC RX-7, but are not commonly found in the American Market. Mazda also introduced Dynamic Tracking Suspension System (DTSS) in the FC. The revised independent rear suspension incorporated special toe control hubs which were capable of introducing a limited degree of passive rear steering under cornering loads. The DTSS worked by allowing a slight amount of toe-out under normal driving conditions but induced slight toe-in under heavier cornering loads at around 0.5g or more; toe-out in the rear allows for a more responsive rotation of the rear, but toe-in allowed for a more stable rear under heavier cornering. Another new feature was the Auto Adjusting Suspension (AAS). The system changed damping characteristics according to the road and driving conditions. The system compensated for camber changes and provided anti-dive and anti-squat effects.

In Japan, a limited edition of the second-generation RX-7 called Infini was available with production limited to only 600 cars for each year. Some special noted features for all Infini series are: infini logo on the rear, upgraded suspension, upgraded ECU, higher power output of the engine, reduced weight, 15-inch BBS aluminum alloy wheels, Infini logo steering wheel, aero bumper kits, bronze-colored window glass, floor bar on the passenger side, aluminum bonnet with scoop, flare, and holder. The car was thought as the pinnacle of the RX-7 series (until the introduction of the third generation RX-7). The Infini IV came with other special items such as black bucket seats, 16-inch BBS wheels, Knee pads, and all the other items mentioned before. There are differing years for the Infini, which denoted the series. Series I was introduced in 1987, Series II was introduced in 1988, Series III was introduced in 1989, and Series IV was introduced in 1990. Series I and II came in White or Black exterior colour, Series III came in Shade Green only, and Series IV came in Shade Green or Noble Green exterior colours. There are only minor differences between the Series models, the biggest change which was from the Series I and II being an S4 and the Series III and IV being an S5.

The Turbo II model uses a turbocharger with a twin-scroll design. The smaller primary chamber is engineered to cancel the turbo lag at low engine speeds. At higher revolutions, the secondary chamber is opened, pumping out 33 percent more power than the naturally aspirated counterpart. The Turbo II also has an air-to-air intercooler which has a dedicated intake on the hood. The intake is slightly offset toward the left side of the hood. In the Japanese market, only the turbocharged engine was available; the naturally-aspirated version was only available for select export markets. This can be attributed to insurance companies in many Western nations penalizing turbocharged cars (thus restricting potential sales). The Japanese market car produces 185 PS (136 kW) in the original version; this engine was upgraded to 205 PS (151 kW) in April 1989 as part of the Series 5 facelift. The limited edition, two-seater Infini model received a 215 PS (158 kW) version beginning in June 1990, thanks to an upgraded exhaust system and high-octane fuel.

Australian Motors Mazda introduced a limited run of 250 'Sports' model Series 4 RX-7s; each with no power steering, power windows or rear wiper as an attempt to reduce the weight of the car.

The Haraguchi RX-7 is a legendary vehicle in the world of drifting, often hailed as an iconic representation of the drift culture that emerged in the 1990s. Built by Mitsuru Haraguchi between 1989 and 1993, this Series 2 RX-7 became famous for its unique style and performance, making it one of the earliest examples of what enthusiasts would come to call a "HotBoi" drift car—a term used to describe cars modified for drifting with an emphasis on aesthetic appeal. Mitsuru Haraguchi was not just a driver; he was a key figure in the underground drifting scene in Japan. The RX-7, with its lightweight body and rotary engine, proved to be an ideal platform for the kind of driving that would push the envelope in terms of control and style. The car was extensively modified for performance, featuring upgrades to its suspension, tires, and engine to suit the demands of drifting. The RX-7's aesthetic was also significant. It showcased a vibrant design that captured the spirit of the drifting scene, often adorned with bold graphics and a striking color scheme that made it instantly recognizable. Tragically, the Haraguchi RX-7 met an unfortunate fate when it was crashed in 1999, yet its impact on the drifting community has been profound. The crash, rather than marking the end of its story, solidified its legendary status. It has since been celebrated in various media, including magazines, videos, and online forums, where enthusiasts pay homage to its legacy. Even today, the legacy of the Haraguchi RX-7 influences the design and customization of drift cars around the world. It remains a symbol of innovation within the drifting culture, representing the fusion of performance driving with creative expression through automotive art.

Convertible

[edit]
1989 Mazda RX-7 convertible (FC)

Mazda introduced a convertible version of the RX-7, the FC3C, in 1988 with a naturally aspirated engine—introduced to the US market with ads featuring actor James Garner, at the time featured in many Mazda television advertisements. Only about 22,000 convertibles were built.

The convertible featured a removable rigid section over the passengers and a folding fabric rear section with heated rear glass window. Power operated, lowering the top required unlatching two header catches, power lowering the top, exiting the car (or reaching over to the right-side latch), and folding down the rigid section manually. Mazda introduced with the convertible the first integral windblocker, a rigid panel that folded up from behind the passenger seats to block unwanted drafts from reaching the passengers—thereby extending the driving season for the car with the top retracted.[10] The convertible also featured optional headrest-mounted audio speakers and a folding leather snap-fastened tonneau cover. The convertible assembly was precisely engineered and manufactured, and dropped into the ready body assembly as a complete unit—a first in convertible production.

Production ceased in 1991 after Mazda marketed a limited run of 500 examples for 1992 for the domestic market only. In markets outside the US, only the turbocharged version of the convertible was available.

North America

[edit]

The Series 4 (produced for the 1986 through the 1988 model years) was available with a naturally aspirated, fuel injected 13B-VDEI producing 146 hp (109 kW; 148 PS) in North American spec. An optional turbocharged model, known as the Turbo II in the American market, was rated at 182 hp (136 kW; 185 PS) and 183 lb⋅ft (248 N⋅m) of torque at 3,500 rpm. The turbo model was introduced at the Chicago Auto Show in February 1986, with a target of 20 percent of overall RX-7 sales.[11]

The Series 5 (1989–1992) featured updated styling and better engine management, as well as lighter rotors and a higher compression ratio 9.7:1 for the naturally aspirated model, and 9.0:1 for the turbo model. The naturally aspirated Series 5's 13B-DEI engine was rated at 160 hp (119 kW; 162 PS), while the Series 5 Turbo was rated at 200 hp (149 kW; 203 PS) at 6,500 rpm and 195 lb⋅ft (264 N⋅m) of torque at 3,500 rpm.

Mazda sold 86,000 RX-7s in the US alone in 1986, its first model year, with sales peaking in 1988.

1988 10th Anniversary RX-7

[edit]
Mazda RX-7 10th Anniversary Edition

Mazda introduced the 10th Anniversary RX-7 in 1988 as a limited production model based on the RX-7 Turbo II. Production was limited to 1,500 units. The 10th Anniversary RX-7 features a Crystal White monochromatic paint scheme with matching white body side moldings, tail light housings, mirrors and 16-inch alloy seven-spoke wheels. There were two "series" of 10th Anniversary models, with essentially a VIN-split running production change between the two. The most notable difference between the series can be found on the exterior- the earlier "Series I" cars had a black "Mazda" logo decal on the front bumper cover, whereas most if not all "Series II" cars did not have the decal. Series II cars also received the lower seat cushion height/tilt feature that Series I cars lacked. Another distinctive exterior feature is the bright gold rotor-shaped 10th Anniversary Edition badge on the front fenders (yellow-gold on the Series II cars). A distinctive 10th Anniversary package feature is the all black leather interior (code D7), which included not just the seats, but the door panel inserts as well and a leather-wrapped MOMO steering wheel (with 10th Anniversary Edition embossed horn button) and MOMO leather-wrapped shift knob with integrated boot. All exterior glass is bronze tinted (specific in North America to only the 10th Anniversary), and the windshield was equipped with the embedded secondary antenna also found on some other select models with the upgraded stereo packages. Other 10th Anniversary Edition specific items were headlight washers (the only RX-7 in the US market that got this feature), glass breakage detectors added to the factory alarm system, 10th Anniversary Edition logoed floor mats, 10th Anniversary Edition embroidered front hood protector and accompanying front end mask (or "bra"), and an aluminum under pan.[12][13]

GTUˢ (1989–1990)

[edit]

In 1989, with the introduction of the facelifted FC RX-7, and to commemorate the RX-7s 8 straight wins in the IMSA GTU class from 1980 to 1987, Mazda introduced a limited model labeled the GTUˢ. Starting with the lightweight base model GTU, the GTUˢ added items found on the Turbo model such as four-piston front brakes, ventilated rear brake rotors, vehicle speed-sensing power steering, one-piece front chin spoiler, cloth-covered Turbo model seats, leather-wrapped steering wheel, 16-inch wheels, 205/55VR tires, and a GTUˢ-only 4.300 viscous-type limited-slip differential (all other FC LSD's were 4.100). This allowed quicker acceleration from the naturally aspirated 13B rotary engine. Although it has been rumored that Mazda built between 100 and 1100 GTUˢ' between 1989 and 1990, there is no official documentation from Mazda on how many have been built. The most reliable way to determine a GTUˢ is by taking the VIN to a Mazda dealer and they can look to see if the internal coding for the car comes up as a GS model designation.[14]

Third generation (FD)

[edit]
Third generation (FD)
Overview
Model codeFD
Also calledɛ̃fini RX-7 (1991–1997)
ProductionOctober 1991–2002
68,589 produced[1]
Model years1993–1995 (North America)
Designer
Body and chassis
Body style2-door coupé
Powertrain
Engine1308 cc 13B-REW twin-turbo twin-rotor
Transmission
Dimensions
Wheelbase2,446 mm (96.3 in)
Length4,285 mm (168.7 in)
Width1,760 mm (69.3 in)
Height1,230 mm (48.4 in)
Curb weight1,218–1,340 kg (2,685–2,954 lb)
The winning concept design for the FD RX-7, designed by Wu-Huang Chin at Mazda's Design Center in Irvine
Rear view

The third-generation RX‑7, (sometimes referred to as FD, chassis code FD3S for Japan and JM1FD for the North America), featured an updated body design. Announced in October 1991, production began later that month before going on sale in December in the domestic Japanese market. Left-Hand-Drive export production began shortly after. The 13B-REW engine was the first-ever mass-produced sequential twin-turbocharger system to be exported from Japan,[17] boosting power to 255 PS (188 kW; 252 hp) in 1992 and finally to 280 PS (206 kW; 276 hp) by the time production ended in Japan in 2002.

For the third-generation RX-7, Mazda organized an internal design competition between its four design studios in Hiroshima, Yokohama, Irvine, and Europe.[18] The winning design came from their Design Center in Irvine and was designed by Taiwanese automotive artist Wu-huang Chin (秦無荒), who also worked on the Mazda MX-5 Miata, with help from Tom Matano.[19] The interior design, though, originated from the Hiroshima design proposal. Mazda's chief designer Yoichi Sato (佐藤 洋一, Satō Yōichi) then helped take the concept design to its final production form.[9]

In Japan, sales were affected by this series' non-compliance with Japanese dimension regulations and Japanese buyers paid annual taxes for the car's non-compliant width. As the RX‑7 was now considered an upper-level luxury sports car due to the increased width dimensions, Mazda also offered two smaller offerings, the Eunos Roadster, and the Eunos Presso hatchback.

The sequential twin-turbocharging system, introduced in 1992, was extremely complex and was developed with the aid of Hitachi. It was previously used on the exclusive-to-Japan Cosmo JC Series. The system used two turbochargers, one to provide 10 psi (0.69 bar) of boost from 1,800 rpm. The second turbocharger activated in the upper half of the rpm range, during full-throttle acceleration – at 4,000 rpm to maintain 10 psi (0.69 bar) until redline.[20] The changeover process occurred at 4,500 rpm, with a momentary dip in pressure to 8 psi (0.55 bar),[21] and provided semi-linear acceleration from a wide torque curve throughout the entire rev range under normal operation.

Under high-speed-driving conditions, the changeover process produced a significant increase in power output and forced technical drivers to adjust their driving style to anticipate and mitigate any over-steer during cornering.[citation needed] The standard turbo control system used 4 control solenoids, 4 actuators, both a vacuum and pressure chamber, and several feet of preformed vacuum/pressure hoses, all of which were prone to failure in part due to complexity and the inherent high temperatures of the rotary engine.[21]

Information about various trims and models is listed as follows:

Series 6 (1992–1995)
Model Power output Torque Gearbox Weight
Type R 255 PS (188 kW; 252 hp) 294 N⋅m (217 lbf⋅ft) 5-speed manual 1,260 kg (2,778 lb)
Type RZ 1,230 kg (2,712 lb)
Type RB 1,260 kg (2,778 lb)
A-Spec 265 PS (195 kW; 261 hp) 1,220 kg (2,690 lb)
EU-Spec 239 PS (176 kW; 236 hp) 294 N⋅m (217 lbf⋅ft) 1,325 kg (2,921 lb)
Touring X 255 PS (188 kW; 252 hp) 4-speed automatic 1,330 kg (2,932 lb)[22]

Series 6 (1992–1995)

[edit]
RX-7 Spirit Type R A-spec with pop-up headlights raised

Series 6 was exported throughout the world and sold in larger numbers than in later years. In Japan, Mazda sold the RX-7 through its ɛ̃fini brand as the ɛ̃fini RX-7. Models in Japan included the Type S, the base model, Type R, the lightweight sports model, Type RZ, Type RB, A-spec and the Touring X, which came with a four-speed automatic transmission.[23] The RX-7 was sold in 1993–1995 in the U.S. and Canada. The Series 6 was rated at 255 PS (188 kW; 252 hp) and 294 N⋅m (217 lb⋅ft).

North American market

[edit]

At launch, three option packages were offered; the unlabeled base model, the Touring and the R1 (renamed R2 in 1994). All cars were only available as a two-seater unlike the previous generation which was a 2+2 configuration in North America. All cars were equipped with the same sequential twin-turbo 13B REW engine. A five-speed manual transmission was standard and a 4-speed automatic was available on the base model and Touring package. A driver-side airbag and anti-lock brakes are standard as well. The Touring package included a glass moonroof, fog lights, leather seats, a rear window wiper and a Bose Acoustic Wave music system with CD player.[21] The R1 (R2 in 1994–95) model featured upgraded springs, Bilstein shocks, an additional engine oil cooler, an aerodynamics package comprising a front lip and rear wing, suede seats and Pirelli Z-rated tires. Cruise control was deleted on the R1.[24] The R2 differed from the R1 in that it had slightly softer suspension.[21]

In 1994, the interior received a small update to include a passenger-side air bag, and a PEG (popular equipment group) package was offered. The PEG package featured leather seats, a rear cargo cover and a power steel sunroof. It did not include the fog lights or Bose stereo of the touring package. An automatic transmission was not available with the PEG.

In 1995, the Touring package was replaced by the PEP (popular equipment package). The PEP included a rear wing, leather seats, sunroof and fog lights, but didn't have the Bose Stereo nor the rear window wiper.[21] An estimated 500 RX-7s were produced for the 1995 model year.[25] This would be the final year of RX-7 production for North America, as it was discontinued due to slow sales.

Australian market

[edit]

A special high-performance version of the RX-7 was introduced in Australia in 1995, named the RX-7 SP. This model was developed to achieve homologation for racing in the Australian GT Production Car Series and the Eastern Creek 12 Hour production car race.[26] An initial run of 25 cars were made, and later an extra 10 were built by Mazda due to demand.[27] The RX-7 SP was rated at 277 PS (204 kW; 273 hp) and 357 N⋅m (263 lb⋅ft) of torque, a substantial increase over the standard model. Other changes included a race-developed carbon fiber nose cone and rear spoiler, a carbon fibre 120 L (32 US gal) fuel tank (as opposed to the 76 L (20 US gal) tank in the standard car), a 4.3:1 final drive ratio, 17-inch wheels, larger brake rotors and calipers. A "three times more efficient" intercooler, a new exhaust, and a modified ECU were also included.[27] Weight was reduced significantly with the aid of further carbon fibre usage including lightweight vented bonnet and Recaro seats to reduce weight to 1,218 kg (2,685 lb) (from 1,250 kg (2,756 lb)) making this model road-going race car that matched the performance of the rival Porsche Carrera RS Club Sport for the final year Mazda officially entered.[26] The formula paid off when the RX-7 SP won the 1995 Eastern Creek 12 Hour, giving Mazda the winning 12-hour trophy for a fourth straight year.[26] The winning car also gained a podium finish at the international tarmac rally Targa Tasmania months later. A later special version, the Bathurst R, was introduced in 2001 to commemorate this victory in Japan only.[28] It was based on the RX-7 Type R and 500 were built in total, featuring adjustable dampers, a carbon fibre shift knob, carbon fibre interior trim, special fog lamps and a different parking brake lever.[29]

Mazda 13B-REW rotary engine

European market

[edit]

In Europe, only 1,152 examples of the FD were sold through the official Mazda network, due to a high price and a fairly short time span. Only one model was available and it included twin oil-coolers, electric sunroof, cruise control and the rear storage bins in place of the back seats.[30] It also has the stiffer suspension and strut braces from the R models.[31] Germany topped the sales with 446 cars, while UK is second at 210 and Greece third with 168 (thanks to that country's tax structure which favored the rotary engine).[32] The European models also received the 1994 interior facelift, with a passenger air bag.[citation needed] Sales in most of Europe ended after 1995 as it would have been too expensive to reengineer the car to meet the new Euro 2 emissions regulations.

United Kingdom
[edit]

In the United Kingdom, for 1992, customers were offered only one version of the FD, which was based on a combination of the US touring and the base model.[30] For the following year, in a bid to speed up sales, Mazda reduced the price of the RX-7 to £25,000, down from £32,000, and refunded the difference to those who bought the car before that was announced. From 1992 to 1995, only 210 FD RX-7s were officially sold in the UK.[32] The FD continued to be imported to the UK until 1996. In 1998, for a car that had suffered from slow sales when it was officially sold, with a surge of interest and the benefit of a newly introduced SVA scheme, the FD would become so popular that there were more parallel and grey imported models brought into the country than Mazda UK had ever imported.[33]

Series 7 (1996–1998)

[edit]

Series 7 included minor changes to the car. Updates included a simplified vacuum routing manifold and a 16-bit ECU which combined with an improved intake system netted an extra 10 PS (7 kW). This additional horsepower was only available on manual transmission cars as the increase in power was only seen above 7,000 rpm, which was the redline for automatic transmission equipped cars. The rear spoiler and tail lights were also redesigned. The Type RZ model was now equipped with larger brake rotors as well as 17-inch BBS wheels. In Japan, the Series 7 RX-7 was marketed under the Mazda and ɛ̃fini brand name.

Series 7 RX-7s were also sold in Australia, New Zealand and the UK. Series 7 models were produced only with right-hand drive (RHD), and were only exported to RHD markets.

Series 8 (1998–2002)

[edit]

Series 8 was the final series, and was only available in the Japanese market. More efficient turbochargers were available on certain models, while improved intercooling and radiator cooling was made possible by a redesigned front fascia with larger openings. The seats, steering wheel, and instrument cluster were all changed. The rear spoiler was modified and gained adjustability on certain models. Three horsepower levels are available: 255 PS (188 kW; 252 hp) for automatic transmission equipped cars, 265 PS (195 kW; 261 hp)for the Type RB, and 280 PS (206 kW; 276 hp) available on the top-of-the-line sporting models.

The high-end "Type RS" came equipped with Bilstein suspension and 17-inch wheels as standard equipment, and reduced weight to 1,280 kg (2,822 lb). Power was increased with the addition of a less restrictive muffler and more efficient turbochargers which featured abradable compressor seals, 280 PS (206 kW; 276 hp) at 6,500 rpm and 314 N⋅m (232 lb⋅ft) of torque at 5000 rpm as per the maximum Japanese limit. The Type RS had a brake upgrade by increasing rotor diameter front and rear to 314 mm (12.4 in) and front rotor thickness from 22 mm (0.9 in) to 32 mm (1.3 in). The Type RS version also sported a 4.30 final drive ratio, providing a significant reduction in its 0–100 km/h (62 mph) time. The gearbox was also modified, 5th gear was made longer to reduce cruising rpm and improve fuel efficiency. The very limited edition Type RZ version included all the features of the Type RS, but at a lighter weight, at 1,270 kg (2,800 lb). It also featured gun-metal colored BBS wheels and a red racing themed interior. An improved ABS system worked by braking differently on each wheel, allowing the car better turning during braking. The effective result made for safer driving for the average buyer.

Mazda RX-7 Spirit R
Instrument panel of RX-7 Spirit R

Easily the most collectible of all the RX-7s was the last model limited to 1,500 units. Dubbed the "Spirit R", they combined all the extra features Mazda had used on previous limited-run specials with new exclusive features like cross-drilled brake rotors. Sticker prices when new were 3,998,000 yen for Type-A and B and 3,398,000 yen for Type-C. Mazda's press release said "The Type-A Spirit R model is the ultimate RX-7, boasting the most outstanding driving performance in its history."

There are three models of "Spirit R": the "Type A", "Type B", and "Type C". The "Type A" is a two-seater with a five-speed manual transmission. It features lightweight red trim Recaro front seats as seen in the earlier RZ models. The "Type B" shares all features of the "Type A" but with a 2+2 seat configuration. The "Type C" is also a 2+2, but has a four-speed automatic transmission. Of the 1,504 Spirit R's made, 1,044 were Type A, 420 Type B and 40 Type C.[34] An exclusive Spirit R paint color, Titanium Grey, adorned 719 of the 1,504 cars produced.

In Japan the FD3S production span is categorized into six models: #1 from 1991/12, #2 from 1993/08, #3 from 1995/03, #4 from 1996/01, #5 from 1998/12 and #6 from 2000/10. The model number (1 to 6) shows as the first digit of the six-characters-long JDM VIN; e.g., in VIN FD3S-ABCDEF, the A is the model number. A total of nine limited editions (type RZ in 1992/10 (300 cars), RZ 1993/10 (150), R-II Bathurst 1994/09 (350), R Bathurst X 1995/07 (777), RB Bathurst X 1997/01 (700), RS-R 1997/10 (500), RZ 2000/10 (325), R Bathurst R 2001/08 (650), Spirit R 2002/04 (1504)) and 2 special editions (Bathurst R 1995/02, R Bathurst 2001/12 (2174)) were produced.[35][36][37]

Series 8 (1998–2002)
Model Power Torque Gearbox Weight Seating Brakes Wheels Tyres
Type RB 265 PS (195 kW; 261 hp) 294 N·m (217 lb·ft) 5-speed manual 1,310 kg (2,888 lb) 2+2 294 mm (11.6 in) 16x8.0JJ (front)
16x8.0JJ (rear)
225/50R16 92V(front)
225/50R16 92V(rear)
Type RB 4AT 255 PS (188 kW; 252 hp) 4-speed automatic 1,340 kg (2,954 lb)
Type RB-S 265 PS (195 kW; 261 hp) 5-speed manual 1,320 kg (2,888 lb) 225/50ZR16 (front)
225/50ZR16 (rear)
Type R 280 PS (206 kW; 276 hp) 314 N·m (231 lb·ft) 1,310 kg (2,888 lb)
Type R
Bathurst
1,280 kg (2,822 lb)
Type R
Bathurst R
Type RS 314 mm (12.4 in) 17x8.0JJ (front)
17x8.5JJ (rear)
235/45R17 (front)
255/40R17 (rear)
Type RZ 1,270 kg (2,800 lb) 2
Spirit R
(Type A)
Spirit R
(Type B)
1,280 kg (2,822 lb) 2+2
Spirit R
(Type C)
255 PS (188 kW; 252 hp) 4-speed automatic 294 mm (11.6 in)

Reviews and awards

[edit]

The RX-7 made Car and Driver magazine's Ten Best list five times (1983, 1987, 1993–1995).

In 2004, Sports Car International named the Series 3 car seventh on their list of Top Sports Cars of the 1970s. In 1983, the RX-7 would appear on Car and Driver magazine's Ten Best list for the first time in 20 years.

Though about 363 kg (800 lb) heavier and more insulated than its predecessor, the FC continued to win accolades from the press. The RX-7 FC was Motor Trend's Import Car of the Year for 1986, and the Turbo II was on Car and Driver magazine's 10 Best list for a second time in 1987.

The FD RX-7 was Motor Trend's Import Car of the Year for 1993. When Playboy first reviewed the FD RX-7 in 1993, they tested it in the same issue as the [then] new Dodge Viper. In that issue, Playboy declared the RX-7 to be the better of the two cars. It went on to win Playboy's Car of the Year for 1993.

The FD RX-7 also made Car and Driver's Ten Best list for 1993 through 1995 – all three years in which it was sold in the United States. In June 2007, Road & Track proclaimed: "The ace in Mazda's sleeve is the RX-7, a car once touted as the purest, most exhilarating sports car in the world." After its introduction in 1991, it won the Automotive Researchers' and Journalists' Conference Car of the Year award in Japan.

Handling in the FD RX-7 was regarded as world-class, and it is still regarded as being one of the finest-handling and best-balanced cars of all time.[38][39]

Motorsport

[edit]
An RX-7 GT3 car, winner of the GT3 class at the 2010 SCCA National Championship Runoffs

Racing versions of the first-generation RX-7 were entered at the prestigious 24 hours of Le Mans endurance race. The first outing for the car, equipped with a 13B engine, failed by less than one second to qualify in 1979. The next year, a 12A-equipped RX-7 not only qualified, it placed 21st overall. That same car did not finish in 1981, along with two more 13B cars. Those two cars were back for 1982, with one 14th-place finish and another DNF. The RX-7 Le Mans effort was replaced by the 717C prototype for 1983.

Mazda began racing RX-7s in the IMSA GTU series in 1979. In its first year, RX-7s placed first and second at the 24 Hours of Daytona, and claimed the GTU series championship. The car continued winning, claiming the GTU championship seven years in a row. The RX-7 took the GTO championship ten years in a row from 1982. In addition to this, a GTX version was developed, named the Mazda RX-7 GTP; this was unsuccessful, and the GTP version of the car was also unsuccessful. The RX-7 has won more IMSA races than any other car model. In the USA SCCA competition RX-7s were raced with great success by Don Kearney in the NE Division and John Finger in the SE Division. Pettit Racing won the GT2 Road Racing Championship in 1998. The car was a '93 Mazda RX-7 street car with only bolt-on accessories. At season end Pettit had 140 points—63 points more than the second place team. This same car finished the Daytona Rolex 24-hour race four times.

The RX-7 also fared well at the Spa 24 Hours race. Three Savanna/RX-7s were entered in 1981 by Tom Walkinshaw Racing. After hours of battling with several BMW 530is and Ford Capris, the RX-7 driven by Pierre Dieudonné and Tom Walkinshaw won the event. Mazda had turned the tables on BMW, who had beaten Mazda's Familia Rotary to the podium eleven years earlier at the same event. TWR's prepared RX-7s also won the British Touring Car Championship in 1980 and 1981, driven by Win Percy.

A Mazda RX-7 Group B rally car which competed in the 1979 Monte Carlo Rally

Canadian-born Australian touring car driver Allan Moffat was instrumental in bringing Mazda into the Australian touring car scene which ran to Group C regulations unique to Australia. Over a four-year span beginning in 1981, Moffat took the Mazda RX-7 to victory in the 1983 Australian Touring Car Championship, as well as a trio of Bathurst 1000 podiums, in 1981 (3rd with Derek Bell), 1983 (second with Yoshimi Katayama) and 1984 (third with former motorcycle champion Gregg Hansford). Privateer racer Peter McLeod drove his RX-7 to win the 1983 Australian Endurance Championship, while Moffat won the Endurance title in 1982 and 1984. Australia's adoption of international Group A regulations, combined with Mazda's reluctance to homologate a Group A RX-7 (meaning that a base number of 5,000 had to be built, plus another 500 "evolution" models), ended Mazda's active participation in Australian touring car racing at the end of the 1984 season. Plans had been in place to replace the RX-7 with a Mazda 929, but testing by Allan Moffat in late 1984 had indicated that the car would be uncompetitive and Mazda abandoned plans to race in Group A.

The RX-7 even made an appearance in the World Rally Championship. The car finished 11th on its debut at the RAC Rally in Wales in 1981. Group B received much of the focus for the first part of the 1980s, but Mazda did manage to place third at the 1985 Acropolis Rally, and when the Group B was folded, its Group A-based replacement, the 323 4WD claimed the victory at Swedish Rally in both 1987 and 1989.

IMSA Bridgestone Supercar Series

[edit]

The third-generation Mazda RX-7 entered its first professional race in the world on February 23, 1992, at the Miami Grand Prix. The cars made it to the podium many times and won the IMSA Supercar race at Sebring in 1994. Peter Farrell Motorsport also fielded RX-7's in the IMSA Firestone Firehawk Endurance Series dominating many races and finishing runner up in the overall championship two years in a row.

Revivals

[edit]

Mazda has made several references to a revival of the RX-7 in various forms over the years since the RX-8 was discontinued. In November 2012, MX-5 program manager Nobuhiro Yamamoto indicated that Mazda was working on a 16X based RX-7, with 300 horsepower.[40][41]

Mazda RX-Vision concept car

In October 2015, Mazda unveiled the RX-Vision concept car at the Tokyo Motor Show, powered by a new rotary engine and featured design cues reminiscent of the third generation RX-7. A production-ready concept could have followed suit by 2017, marking 50 years since the revealing of Mazda's first rotary-powered sports car, the Cosmo.[42]

Mazda Iconic SP concept car

In October 2023, Mazda unveiled the Iconic SP concept car at the Japan Mobility Show, powered by a two-rotor rotary engine and also features design cues reminiscent of the third generation RX-7, most notably its pop-up headlights.[43]

References

[edit]

Citations

[edit]
  1. ^ a b c d e Long, Brian (2004). RX-7. Dorchester: Veloce Publishing. p. 206. ISBN 978-1-904788-03-4.
  2. ^ Lewis-George, Elliot (2013). Berg, Nik (ed.). "Mazda Heroes #1 – Ikuo Maeda". Zoom-Zoom Magazine (16): 6. Archived from the original on 2 February 2014. Retrieved 15 May 2013.
  3. ^ a b Hogg, Tony (ed.). "1981 Buyer's Guide". Road & Track's Road Test Annual & Buyer's Guide 1981 (January–February 1981): 105.
  4. ^ Hall, Jim, ed. (November 1982). "International Report: Mazda Shows Limited-Edition RX-7". Motor Trend. Vol. 34, no. 11. Petersen Publishing Co. p. 24.
  5. ^ Büschi, Hans-Ulrich, ed. (March 10, 1983). Automobil Revue '83 (in German and French). Vol. 78. Berne, Switzerland: Hallwag, AG. p. 363. ISBN 978-3-444-06065-6.
  6. ^ "Development of Low-Emission Rotary Engines Archived 2010-01-16 at the Wayback Machine", Mazda Motor Corporation
  7. ^ Dieudonne, Pierre (1983-12-15). "Ballade Japonaise: à la découverte des Mazda Turbo" [Japanese ballad: Discovering the Mazda Turbos]. Le Moniteur de l'Automobile (in French). 34 (784): 40.
  8. ^ Dieudonne, pp. 43-44
  9. ^ a b 望月, 澄男 (2017). マツダRX-7 (PDF) (in Japanese). Japan: Miki Press. p. 21. ISBN 978-4-89522-675-2. Archived from the original (PDF) on 2020-02-19.
  10. ^ Cranswick, Marc (2016). Mazda Rotary-engined Cars: From Cosmo 110S to RX-8. Veloce Publishing Ltd. p. 136. ISBN 978-1845849436. ISBN 9781845849436.
  11. ^ Smith, David C., ed. (March 1986). "Mazda eyes midsize U.S. market". Ward's Auto World. 22 (3). Ward's Communications: 30.
  12. ^ McCourt, Mark J. (2015-03-23). "A Decade of Delight: 1988 Mazda RX-7 10th Anniversary Limited Edition brochure". Hemmings. Retrieved 2019-04-19.
  13. ^ Constantine, Chris (2018-01-08). "Limited Edition 1988 Mazda RX-7 Turbo 10th Anniversary for Sale". The Drive. Retrieved 2019-04-19.
  14. ^ Tonn, Chris (2015-11-04). "Digestible Collectible: 1989 Mazda RX-7 GTUs". Retrieved 2019-04-19.
  15. ^ Yuan, Dave (2016-12-28). "25 Year Club: FD3S Mazda RX-7". Japanese Nostalgic Car. Retrieved 2019-09-01.
  16. ^ Long, Brian (1 December 2003). RX-7 Mazda's Rotary Engine Sports Car: Updated & Enlarged Edition. Veloce Publishing Ltd. ISBN 9781904788034. Retrieved 9 July 2017 – via Google Books.
  17. ^ "Mazda pays tribute to the RX-7". Archived from the original on 2018-11-16. Retrieved 2018-11-16.
  18. ^ McAleer, Brendan. "How the Jaguar E-Type Influenced the FD Mazda RX-7". Road & Track.
  19. ^ O'Dell, John (30 January 1995). "Design Central". Los Angeles Times. a concept car whose design was inked at Mazda Research & Design in Irvine in 1989. It evolved into the curvy third-generation Mazda RX‑7 for the 1993 model year. The design was the work of 37-year old Wu-Huang Chin, above, who also was a member of the Miata design team.
  20. ^ "Mazda RX-7 FD - review, history, prices and specs". Evo. Retrieved 2018-11-16.
  21. ^ a b c d e "Your definitive Mazda RX‑7 FD buyer's guide | Hagerty Articles". Retrieved 2018-11-16.
  22. ^ "1993 Efini RX-7 (FD-series) Type 2".
  23. ^ "Detailed specs review of 1994 Efini RX-7 Touring X model for Japan". www.automobile-catalog.com. Retrieved 2019-01-19.
  24. ^ "Looking Back: Driving A Bone-Stock 1993 Mazda RX-7 R1". DrivingLine. 5 September 2018. Retrieved 2018-11-16.
  25. ^ "Your definitive Mazda RX-7 FD buyer's guide". 8 May 2018.
  26. ^ a b c Robinson, James (2016-09-16). "Uber rare RX-7 at Shannon's". motoring.com.au. carsales.com Limited. Archived from the original on 2016-09-17.
  27. ^ a b "Mazda Australia's RX7-SP and RX7-SP2 (3rd Generation RX7)". 2001-03-22. Archived from the original on 2015-05-27.
  28. ^ "Mazda RX-7 Type R Bathurst R Review". TradeUniqueCars.com.au. Retrieved 2018-11-16.
  29. ^ "2001 Mazda RX-7 Type R Bathurst | Review | SuperCars.net". Supercars.net. 2016-04-24. Retrieved 2018-11-16.
  30. ^ a b "Mazda RX-7 | Used Car Buying Guide". Autocar. Retrieved 2021-12-09.
  31. ^ "Mazda RX-7 FD - review, history, prices and specs". evo. Retrieved 2021-12-09.
  32. ^ a b "Top Gear's mk3 Mazda RX-7 buying guide". Top Gear. 2018-03-12. Retrieved 2018-11-16.
  33. ^ "The Complete History Of The Mazda RX-7 - Garage Dreams". Garage Dreams. 2018-02-05. Retrieved 2018-11-16.
  34. ^ "Mazda RX-7 FD3S Spirit-R". GTR-Registry.com. Retrieved 3 March 2019.
  35. ^ I Love FD3S RX-7, book in Japanese ISBN 4-87366-999-5
  36. ^ "History of RX-7" (in Japanese). Mazda. Retrieved 19 July 2022.
  37. ^ "Mazda RX-7 FD3S Series 8 (Version V + Version VI)". GTR-Registry.com. Retrieved 3 March 2019.
  38. ^ "The Mazda RX-7 (FD) is Beautifully Engineered". Tumblr. Retrieved 9 July 2017.
  39. ^ http://www.jdmcarboy.com/category.php?id_category=1392[permanent dead link]
  40. ^ "New Mazda RX-7 to launch by 2017". leftlanenews.com.
  41. ^ "Mazda RX-7 to Return in 2017". CarBuzz. 4 November 2012.
  42. ^ Tisshaw, Mark (2015-10-28). "Mazda RX-Vision rotary-engined sports car concept revealed". Autocar.co.uk.
  43. ^ "MAZDA NEWSROOM|Mazda unveils 'MAZDA ICONIC SP' compact sports car concept|NEWS RELEASES". Mazda News Releases. 2019-05-05. Retrieved 2023-10-25.

General sources

[edit]

Further reading

[edit]
  • Mauck, Scott & Haynes, John H. (1986). Mazda RX-7 Automotive Repair Manual. Haynes North America. ISBN 978-1-85010-050-8.
  • Yamaguchi, Jack K. (1985). The New Mazda RX-7 and Mazda Rotary Engine Sports Cars. New York: St. Martin's Press. ISBN 978-0-312-69456-2.
  • Heimann, Jim, ed. (2006). 70s Cars. TASCHEN GmbH. ISBN 978-3-8228-4800-5.
  • Matras, John (1994). Sports Car Color History Mazda RX-7. Motorbooks International. ISBN 978-0-87938-938-3.
[edit]